Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair Services in Farmers Branch, TX
If a driveway gate in Farmers Branch won’t open, sags against the latch post, or starts and stops mid-travel, the fix usually comes down to a hinge, a sensor, or an operator that has reached the end of its working life. We handle all three, and Hal Gatewood runs every job himself. Call (325) 936-1371 and a live person answers, day or night.
This isn’t a place where you should gamble on a national outfit that sends somebody from three counties over and quotes one price on the phone and another at your door. You want a name you can look up, a shop you can drive to, and a person who will answer when the gate acts up again in July. That’s how we’ve always worked.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Why Farmers Branch Homeowners Choose Gatewood Fence & Gate
Farmers Branch is a small city with a lot of industrial traffic, and that shapes the kind of gate work we get called for. We run service through neighborhoods near Valwood Parkway, the residential streets off Webb Chapel Road, and the older ranch-style blocks around Rawhide Park. The calls are split between ornamental iron driveway gates from the nineties and early two-thousands, and commercial slide gates and access-control systems along the I-635 corridor.
Hal Gatewood started this shop in 2001, and his name is still on the invoice and on the front of the building. That matters to people who’ve been burned before. When you call, you’re not reaching a call center. You’re reaching the person who will show up, or someone sitting ten feet from him. Every job gets the 90-Day Done Right Promise in writing. If it’s not right, one call brings us back, no runaround. We serve Farmers Branch with background-checked, uniformed crew members, and we stand behind the work whether it’s a $200 hinge repair or a full commercial access-control rebuild.
Gate Repair Services We Offer in Farmers Branch
Gate Repair
A sagging gate is almost never a bent gate panel. It’s a failed hinge post, a worn pintle, or a weld that cracked from years of North Texas clay shifting underneath it. We find the real cause before we touch a wrench, and we weld on site so your gate stays in your driveway where you can watch the work.
Learn more about our gate repair in Farmers Branch.
Gate Installation
A new driveway gate in Farmers Branch has to be engineered for the soil it sits in. We set posts deeper than the shrink-swell zone, use proper gate frames for the panel weight, and match the operator to the duty cycle the gate will actually see. We measure free, quote upfront, and never start work until you’ve agreed to the number on paper.
Learn more about our gate installation in Farmers Branch.
Gate Motor & Opener
First-generation swing operators on those nineties ornamental gates are hitting the end of their service life around now, and a lot of them were mounted without shade. Summer heat pushing past 100°F causes thermal cutoffs to trip and cooks the wiring insulation. We stock parts for LiftMaster, FAAC, Mighty Mule, and Elite, and we can usually tell you what’s really wrong in the first fifteen minutes.
Learn more about our gate motor and opener service in Farmers Branch.
Gate Access Control
In Farmers Branch, access control often means commercial. Keypad entry at a corporate HQ gate, a card reader on a logistics yard slide gate, a phone-entry system at a parking facility off Valwood. We wire, program, and troubleshoot these systems as often as we do residential openers, and we know the loop-detector side of it cold.
Learn more about our gate access control work in Farmers Branch.
Gate Parts & Welding
When a hinge post breaks at the base or a weld cracks on an iron gate, the answer is not a whole new gate. It’s on-site welding, a new pintle, a reinforced post, maybe a fresh set of bearings. We repair first and replace only what actually needs replacing. If somebody quoted you a full replacement and it didn’t sit right, bring us the estimate. We’ll give you a free second opinion.
Learn more about our gate parts and welding in Farmers Branch.
What to Look For (and What We Look At) in Farmers Branch
Before you call anybody, there are a few things worth knowing. None of these require you to turn a wrench yourself, and honestly, you shouldn’t. Gate springs and torsion systems carry enough tension to do real damage. Leave the repair to somebody who does it daily.
What to check:
– Does the gate hesitate or reverse midway?
– Does it sag toward the latch side, leaving a gap at the bottom?
– Does the operator whine or grind, or just click?
– Is the keypad or receiver dead after a storm?
– Are there fresh cracks in the concrete at the base of a post?
What we look at when we arrive: the plumb of the hinge post first, then the panel alignment, then the operator and its limits, then the safety edges and photo eyes, then the loop detector if there is one. In Farmers Branch, that last one fails more than most people expect.
Why Farmers Branch’s Climate & Housing Affect Gate Repair
Farmers Branch sits on North Texas black clay, the Vertisol soil that swells when it rains and cracks when it’s dry. That soil moves, and when it moves, it takes gate posts with it. A post that was dead plumb in April can lean an inch by August, and an inch at the post means two inches at the latch. This is the single biggest driver of misalignment calls we get in the residential pockets around Farmers Branch. The fix is not to tug on the gate. The fix is to reset or reinforce the post, sometimes with a deeper footing or a steel core.
Then there’s the heat. Operators mounted on the west side of a brick column, no shade, black metal housing, direct afternoon sun on a 104-degree day. The thermal cutoff trips, the gate stops halfway, and the homeowner thinks the motor is dead. Often it’s the wiring insulation, UV-brittle after two decades of North Texas sun, shorting inside the jacket. And out along Valwood Parkway, the heavy truck traffic chews through the asphalt and tears up the inductive loop detectors embedded in commercial driveways. Loop failure is a disproportionately common call for us in Farmers Branch compared to the purely residential suburbs around it. If a technician can’t diagnose and re-wire a failed loop, they’re leaving half the commercial work in this city on the table.
Pricing for Gate Repair in Farmers Branch
- Hinge or pintle replacement: $180-$340, materials included.
- On-site weld repair (cracked panel or post): $250-$480 depending on access and extent.
- Swing gate operator replacement: $900-$1,800 installed, depending on brand and gate weight.
- Slide gate operator replacement: $1,400-$2,800 installed, depending on travel and duty cycle.
- Loop detector replacement or re-wire: $300-$600, including saw-cutting and sealant.
- Full access-control package (keypad, receiver, photo eyes, safety edges): $700-$1,500 installed.
You get $40 off any repair over $200, and seniors and veterans get a permanent 10% discount. Call (325) 936-1371 and we’ll give you a written number before any work begins.
Neighborhoods We Serve in Farmers Branch
We work all over Farmers Branch, but these are the areas we’re in most weeks. Typical response time in the city is same-day for repairs and next-day for installations, depending on the parts.
- Valwood Industrial Corridor and the commercial properties along Valwood Parkway
- Residential streets off Webb Chapel Road
- The ranch-style neighborhoods around Rawhide Park
- Areas near the I-635 frontage and the corporate campuses at the city’s eastern edge
- The established blocks between Josey Lane and Interstate 35E
Service Area - Cities Near Farmers Branch
We also run service into the surrounding metro. If you’re in Highland Park, Dallas, Plano, or Irving, the same shop and the same promise apply. Learn more about our home service area or call us directly.
Serving Farmers Branch, TX - Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Farmers Branch
How much does gate repair cost in Farmers Branch?
Most hinge, pintle, and weld repairs in Farmers Branch run between $180 and $480. Operator replacements start around $900 for a residential swing-motor job and go up from there for slide gates. The price is quoted and agreed before any work starts, and it doesn’t change at the door. Call (325) 936-1371 for a written estimate, free.
Can you come today?
Repair calls in Farmers Branch can often be scheduled same-day, especially if the gate is stuck open or blocking access. Commercial slide-gate and loop-detector work may need a next-day slot depending on parts. Call (325) 936-1371 and tell us what the gate is doing. We’ll give you a straight answer on timing.
What does a full gate installation include?
A full installation from us includes the free measure, the gate panel or frame, the hinge hardware and posts spec’d for the soil, the operator, the safety photo eyes and edges, the power run to the opener, and the programming. Everything is itemized and written before work begins, and we never substitute brands without telling you first. Learn more about our gate installation in Farmers Branch.
Do you handle the power run and the safety edges?
Yes. We run the power from the panel or nearest source, install the photo eyes and safety edges, set the limits, and test the auto-reverse. A gate that doesn’t reverse when it hits something is a liability, and we don’t leave a job until that works. Call (325) 936-1371 with your address and we’ll tell you what’s involved.
What’s the 90-Day Done Right Promise?
It’s written on every invoice. If something we fixed or installed doesn’t hold up within 90 days, one call brings us back and we make it right. No forms, no dispute process, no “that’s normal wear.” Hal Gatewood’s name is on the paper, and he takes that personally.
Call Gatewood Fence & Gate in Farmers Branch, TX
If your gate is acting up, or it’s been doing it for a while and you’re tired of nursing it along, call (325) 936-1371. A live person answers, 24/7. We’ll ask what the gate is doing, tell you what we think over the phone, and get you on the schedule. Estimates are free, the trip charge inside the county is zero, and the price is the price, on paper, before the first tool comes off the truck.
If you already have a written estimate from another company, bring it over. We’ll give you a free second opinion. Hal will point at what’s actually wrong and what isn’t, and he’ll tell you straight whether the gate needs a fix or a full replacement. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Farmers Branch and the surrounding metro since 2001.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Farmers Branch Customers Say
"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg