Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Highland Park, TX | Gatewood Fence & Gate
We provide independent Gate Repair in Highland Park for Ghost Controls systems, and the work here looks different than it does ten minutes south in Dallas. The quick answer: most Ghost Controls failures we see in Highland Park trace back to the Blackland Prairie clay shifting under post footings, which throws swing gate travel limits out of alignment. Hal Gatewood has been fixing these systems since 2001, and we stock OEM Ghost Controls parts locally for same-week turnaround. Call (325) 936-1371 for a free estimate.
Why Highland Park Residents Choose Us for Ghost Controls Service
We’re an independent Ghost Controls service provider, not a factory shop and not a franchise. What that means in practice: we fix the opener you have rather than steering you toward a full replacement when a $40 limit switch is the actual problem. Hal Gatewood grew up about a mile from the Katy Trail corridor and has been working on gates in and around Highland Park long enough to have repaired the same driveway gate twice for the same family, fifteen years apart. He learned welding and metal fabrication at Eastfield College and brings that shop skill to every job site. Their name is on the shop, the address is published, and when you call, a live person answers. That is not a marketing line. It is how Hal runs the place.
We know Ghost Controls’ proprietary gate systems from years of independent service on Highland Park’s ornate estates. The AXDP, TSS1, and DTP1 series each have their own failure patterns, and we have seen all of them on homes along Beverly Drive, Armstrong Parkway, and the smaller streets off Preston Road. For deeper background on the brand, see our Ghost Controls sales & service page. For area coverage details, visit Highland Park service area.
Common Ghost Controls Gate Repair Problems We Solve in Highland Park
- Limit switch drift from post footing movement. Highland Park sits on expansive clay that swells in spring and cracks in August. When the post shifts even half an inch, a Ghost Controls swing gate over-travels or stalls mid-cycle. We repack the footing and recalibrate the travel limits, which fixes the underlying problem instead of just resetting the switch and hoping.
- Moisture intrusion into the control board enclosure. North Texas spring storms hammer Highland Park with driving rain, and the factory control box on older Ghost Controls units lets water in around the gasket. The receiver fails intermittently, the gate opens when it should not or fails to respond to the remote. We open the enclosure, dry it out, replace the damaged board if needed, and reseal the gasket properly.
- Corrosion on arm assembly pins and quick-release brackets. Dallas drought dust plus lawn irrigation overspray is a recipe for surface rust that eventually seizes the pivot pins on Ghost Controls actuator arms. The gate gets stiff, then binds. We free the pins, replace corroded hardware with quality aftermarket fasteners where appropriate, and lubricate the assembly so it cycles smoothly.
- Battery backup failure after power surges. The February 2021 freeze and the outages that followed damaged charging circuits in a lot of Ghost Controls battery backup systems. The gate works on AC power but dies the moment the power cuts out, which is exactly when you need the backup. We test the charging circuit, replace the battery or the board as needed, and confirm the system actually holds a charge.
- Travel limit misalignment on original 1940s and 1950s gates. Highland Park’s older ornamental iron gates predate automation by 40 to 60 years. When a Ghost Controls operator is bolted onto an original swinging panel, the actuator’s travel path has to be set precisely or the gate slams at the end of its stroke. We match the operator’s throw to the gate’s actual leaf weight and geometry, which keeps the original iron from racking.
Ghost Controls Service in Highland Park: What Local Conditions Mean for Your Equipment
Highland Park’s town building department enforces a rule that any repaired or replaced ornamental gate must match the original ironwork profile and finish. That sounds like a paperwork detail until you need a Ghost Controls operator swap on a 1940s estate. A bolt-on arm bracket that would be fine in Richardson or Coppell will get flagged here because it does not match the solid round bar stock in the original gate. So we fabricate a period-correct arm bracket in the driveway, match the finish, and install the new Ghost Controls actuator onto it. The repair is invisible unless you know exactly where to look. This is the part of the job a generic gate company skips, and it is the part the town and the homeowner both notice.
Ghost Controls Models & Products We Service in Highland Park
We service the full Ghost Controls lineup that shows up on Highland Park driveways. That includes the AXDP series dual swing gate opener kits, the TSS1 heavy-duty single swing openers, the DTP1 dual swing openers with battery backup, and the WGT1 wireless keypad and intercom integration components. For critical parts like control boards and motors, we source genuine Ghost Controls OEM components whenever they are available. For batteries, harnesses, and fasteners, we use quality aftermarket equivalents that hold up to Texas heat and keep the repair cost reasonable. Older Ghost Controls models that the manufacturer no longer supports get an honest repair-versus-replace comparison. We recommend a full opener swap only when the motor or gearbox is genuinely worn beyond reliable operation, not because it is easier for us.
Ghost Controls Service Pricing in Highland Park
Ghost Controls gate repair in Highland Park typically runs between $180 and $450 depending on the failure. A limit switch replacement or travel limit recalibration sits at the lower end. A control board replacement with a new OEM part runs higher, especially on the DTP1 series with battery backup. A full opener swap on an older unit lands at the top of that range once you factor in the new actuator and installation labor. Every estimate is quoted and agreed before any work starts, so the number you approve is the number on the invoice. We offer $40 off any repair over $200, no trip charge inside the county, and a free second opinion on any written estimate you already have. Call (325) 936-1371 for an exact quote, estimates are free.
Serving Highland Park, TX - Our Local Coverage Area
We’re based in the Highland Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Highland Park
Yes, and this is half the work we do in Highland Park. Original 1940s ornamental iron gates predate modern automation, which means the Ghost Controls opener was retrofitted onto the gate at some later date. We fabricate period-correct brackets that match the original ironwork profile, install or repair the opener, and set the travel limits so the historic gate swings without racking. The repair looks like it belongs. Call (325) 936-1371 and we will come take a look.
The Blackland Prairie clay under Highland Park swells when spring rain saturates the ground, and that swelling shifts your gate post footings. A Ghost Controls swing gate is calibrated to a specific travel path, and when the post moves even slightly, the actuator’s limit sensor trips mid-swing and the gate stalls. We repack the footings, realign the posts, and recalibrate the travel limits so the gate cycles cleanly through its full arc.
Call us before you assume the battery itself is dead. The February 2021 freeze damaged a lot of Ghost Controls charging circuits through power surges, not the batteries. The gate runs on AC power but the backup will not hold a charge. We test the charging circuit, replace the board or the battery as needed, and verify the system actually holds a charge under load. Call (325) 936-1371 and we will diagnose it properly.
Yes. Most Ghost Controls openers, including the AXDP, TSS1, and DTP1 series, accept wired trigger inputs from external intercom, keypad, and access control systems. We handle the low-voltage wiring integration, match the trigger protocol to your existing system, and test the full open-close cycle with your intercom or keypad before we leave. This is standard work on Highland Park estates with gated driveways and camera entry.
We remove the rust mechanically rather than sandblasting the whole arm, then treat the area with a corrosion inhibitor and refinish the affected spots to match. The goal is to stop the rust without stripping the patina off the surrounding ironwork, which is what a heavy-handed repair does. For arm assembly pins that are too far gone, we replace the hardware with quality aftermarket pieces and keep the visual profile intact. Call (325) 936-1371 for an exact quote.
Service Areas Near Highland Park
We handle Ghost Controls gate repair across Highland Park and the surrounding communities, including Ghost Controls service in Dallas, Ghost Controls service in Plano, Irving, Richardson, and Coppell. That said, Highland Park is where the ornament iron density and the Ghost Controls opener failure patterns keep us busiest.
Book Your Ghost Controls Service in Highland Park Today
Call (325) 936-1371 and we will get your Ghost Controls gate working again. Same-day service is available for urgent failures, and every job carries the 90-Day Done Right Promise in writing. Tell me what it’s doing wrong and I’ll come take a look, here’s my cell.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Highland Park since 2001.