Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Richardson
Gate installation in Richardson runs roughly $1,800 to $6,500 for a standard residential driveway gate, and $3,500 to $12,000+ for a commercial slide gate along the US-75 corridor. Most residential jobs take one to two days once materials are on hand. Call (325) 936-1371 and Hal will walk you through what your specific lot actually needs. We’ve been welding and setting gates since 2001, and we know Richardson’s clay soil and tight setbacks better than any out-of-town outfit ever will.
Why Gatewood Fence & Gate Is Richardson’s Preferred Gate Installation Company
We’re the ones Richardson homeowners call after a national company quoted one price on the phone and showed up with a different number. Hal Gatewood’s name is on the shop and on every invoice. Our 90-Day Done Right Promise is stamped in writing on every job, and if something isn’t right, one call brings him back. No runaround.
The local angle matters here. Richardson isn’t a flat, simple suburb. The Blackland Prairie clay heaves and shrinks through wet-dry cycles that rack gate posts out of square within a season or two if the footing wasn’t dug deep enough. We see it constantly in the 1970s and 1980s ranch neighborhoods off Custer Parkway and Arapaho Road. A crew that doesn’t know this soil will set a post two feet down and call it done. We go deeper, and we build for the shrink-swell cycle, not for a photo finish.
Richardson customers also deal with HOA finish rules in the newer master-planned pockets, plus a heavy load of commercial gate work along the US-75 Telecom Corridor. We’re comfortable with both. LiftMaster and FAAC slide operators on tech campuses, and cedar privacy gates on Canyon Creek and Reservation neighborhoods. Same crew, same warranty. Call (325) 936-1371 and a live person answers, day or night. Not a voicemail, not a call center three states away.
Our Gate Installation Services in Richardson
Driveway Gate Installation in Richardson
Driveway gates are the bread and butter for Richardson’s ranch-style subdivisions like Cottonwood Heights and Duck Creek. Typical residential driveway gate installation runs $2,200 to $5,500 depending on width, material, and whether you’re adding an operator. Most Richardson lots have room for a standard swing gate, but we always measure the setback first. A shared driveway off Custer Parkway changes everything: a swing gate there can block your neighbor’s access, and Gate Installation on a shared right-of-way needs a slide gate or a carefully planned swing arc. We’ll tell you which one fits before we order a single part.
Pedestrian Gate Installation in Richardson
Pedestrian gates are common alongside driveways in older Richardson neighborhoods like Richardson Heights and University Estates. A matching pedestrian gate runs $600 to $1,800 installed, depending on height and material. We build them to match the existing fence line and finish, which matters when the HOA inspects. The concrete and steel hold up to the North Texas UV load better than untreated pine, and we’ll set the post below the clay’s active zone so it doesn’t heave out of plumb in the first wet spring.
Sliding Gate Installation in Richardson
Sliding gates are what we recommend most often along Richardson’s commercial corridors and on residential lots where a swing gate won’t clear. On a shared driveway off Custer Parkway, our crew installed a LiftMaster-powered slide gate for a 1980s brick ranch where Blackland Prairie clay had racked the old swing gate out of square. We poured a new post footing with rebar and ran conduit for a safety photocell, keeping the existing keypad entry working while we removed the old hinge post. That job wouldn’t have survived another wet-dry cycle with a swing gate. A slide gate was the only honest fix. Residential slide gates in Richardson run $2,800 to $6,000; commercial slide gates with operators start around $5,500 and go up based on track length, operator brand, and access control needs.
Swing Gate Installation in Richardson
Where the lot allows, a swing gate remains the most economical option for Richardson driveways. Double swing gates run $2,000 to $4,800 installed, singles less. But in Richardson specifically, swing gates on shallow setbacks are a recurring problem. If the gate swings toward the street, it can clip a car parked in the driveway or block the sidewalk. In older sections around Yale Park and Spring Creek, setbacks are irregular, and we’ve seen plenty of gates that should have been slides from day one. We’ll walk the site with you and show you the difference before you spend a dollar. If a swing fits, we build it with reinforced hinge posts and adjustable hinges so the Blackland Prairie clay doesn’t bind the gate within two seasons.
Security Gate Installation in Richardson
Security gates are a different animal. Along the US-75 corridor between Campbell Road and Renner Road, we install slide gates with loop detectors, card readers, and intercom systems for mid-size tech and telecom campuses. These jobs require keeping vehicle access live during shift changes, which means staging the work around traffic patterns and never blocking the entry. On the residential side, Richardson homeowners in gated pockets or those adding a perimeter entry often want ornamental iron or steel with restricted-access controls. Security gate installs in Richardson run $4,500 to $14,000 depending on the access control package and gate construction. The critical piece is the safety system: photocells, edge sensors, and a properly tuned motor. Skip those and you have a liability, not a gate.
Double Gate Installation in Richardson
Double gates, or paired swing gates, are common on wider driveways in Richardson’s newer sections and larger ranch lots east of Plano Road. Installation runs $2,400 to $5,800 for a standard pair, more with ornamental iron and automation. The catch with double gates on clay soil is that both posts move independently. If one post heaves and the other doesn’t, the gate leaves separate and the latch won’t catch. We set both posts in the same concrete pour, below the shrink-swell line, and we use a center catch that tolerates minor movement. For Richardson’s freeze-thaw cycles and the occasional hard ice storm, that tolerance is the difference between a gate that works in February and one that you have to shoulder open.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Richardson
We’re certified to service nine major gate brands, and for Richardson work we most often install LiftMaster, FAAC, and Linear operators. These are the brands we stock parts for locally, which means faster turnaround when something fails. If a BFT operator on a commercial site near Renner Road goes down, we’re not waiting a week on a distributor. We carry common boards, loop detectors, and photocells on the truck. When you call about a new install or a replacement, we’ll recommend the brand that fits your specific Richardson site, not the one with the biggest rebate.
Common Gate Installation Problems We See in Richardson Homes
- Shallow post footings in Blackland Prairie clay. Richardson’s expansive clay swells when wet and shrinks in drought, cycling gate posts sideways until hinges bind. A footing that stops two feet down will fail within a couple of seasons. We dig below the active clay zone and reinforce with rebar.
- Swing gates on shared driveways with no swing clearance. Older Richardson neighborhoods like Canyon Creek and Duck Creek have shared drives and narrow rights-of-way. A swing gate there can block the neighbor’s access or clip the alley. A slide gate or a pedestrian gate is often the right call.
- Missing or bypassed safety photocells on automated gates. We see this constantly on tech-campus entries along US-75. Someone disables the photocell because a delivery truck can’t trip the loop detector, and now the gate will close on a vehicle. We install loop detectors and edge sensors so the gate opens reliably and never closes on anything.
- Untreated wood gates bleaching and warping under the North Texas sun. Richardson’s UV load is brutal on cedar and pine. Untreated boards check and warp within a few seasons, and the frames rack after two or three ice storms. We build with treated stock and reinforced corners, or recommend powder-coated steel for long-term durability.
Pricing for Gate Installation in Richardson, TX
Here’s what we quote for Richardson work, based on jobs we’ve done on the ground.
- Single swing gate, wood or ornamental steel: $1,800 - $3,200
- Double swing gate, steel frame with wood infill: $2,400 - $5,800
- Pedestrian gate, matching existing fence: $600 - $1,800
- Slide gate, residential, with LiftMaster or FAAC operator: $2,800 - $6,500
- Security slide gate, commercial, with loop detector and access control: $5,500 - $14,000
- Clay-adjusted deep post footing (per post of this type on problematic soil): $250 - $450 above standard footing cost
The price is quoted and agreed before any work starts. No surprises at the door. Visit Gate Installation in Richardson for more on what’s involved. We offer a free second opinion on any written estimate, $40 off any repair over $200, and no trip charge inside the county. Seniors and veterans get a permanent 10% discount. Call (325) 936-1371 for an exact quote.
We Also Serve Cities Near Richardson
Our crew works all over the north Dallas metro. In addition to Richardson, we install gates in Addison, Plano, Dallas, and Coppell. Same owner-operated crew, same 90-Day Done Right Promise. If you’re just over the city line, call (325) 936-1371 and we’ll set a window that works for you.
Serving Richardson, TX - Our Local Coverage Area
We’re based in the Richardson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Richardson
Yes, and in most Richardson neighborhoods with tight setbacks or shared driveways, a sliding gate is the better choice. We install slide gates on lots along Custer Parkway, Arapaho Road, and the older residential streets west of US-75 where a swing arc would block the sidewalk or a neighbor’s access. The gate slides parallel to the fence line instead of swinging into the driveway, so it works on shallow setbacks. We’ll measure your specific right-of-way and show you what fits before any work starts. Call (325) 936-1371 for a free site walk in Richardson.
We stage the work around your traffic, not the other way around. On commercial slide gate replacements along the US-75 corridor between Campbell and Renner, we leave the existing operator running until the new gate is ready to hang, then swap during a low-traffic window. If the site has security requirements, we coordinate with your facilities team so card readers and loop detectors stay live. We’ve done this on enough Richardson tech campuses to know that vehicle access never stops, not even for an install. Call (325) 936-1371 and ask for Hal.
Yes. Every automated gate we install in Richardson has photocells, edge sensors, and proper force settings. It’s not optional and we won’t install a gate without them. Photocells stop the gate if a car, person, or pet breaks the beam while the gate is moving. The North Texas ice storms can freeze a gate track and spike motor load, so the safety system also needs to be tuned for Richardson’s freeze-thaw cycles, not just the summer heat. Call (325) 936-1371 if you want us to check an existing gate that’s missing or bypassing its photocells. That’s a repair, not a full install, and we’ll quote it before we touch anything.
Yes, and this is a common setup in Richardson’s older neighborhoods. We build a steel or wood pedestrian gate beside the slide gate, keeping the person gate set back far enough that it never interferes with the sliding track. On narrow rights-of-way, we’ll use a compact post layout with the pedestrian gate hung on its own footing, independent of the slide gate’s track. That way one doesn’t move the other when the clay shifts. The finished setup keeps foot traffic off the driveway and vehicle access clean. Call (325) 936-1371 and we’ll walk your lot and measure what fits.
The answer depends on your HOA’s finish standard, but in most Richardson neighborhoods with ornamental iron requirements, we install steel gates with a powder-coated finish matched to the HOA palette. Powder coating holds up to the North Texas UV load far better than wet paint, and it won’t chalk or fade the way older painted iron does. We’ll request the HOA’s finish spec before ordering, and we’ll match the color exactly rather than approximating. If the HOA allows, we’ll also match the existing fence style and picket spacing so the gate doesn’t look like an afterthought. Call (325) 936-1371 for a quote on your specific HOA requirements in Richardson.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Richardson with Gate Installation since 2001.
Ready to talk about your gate? Call (325) 936-1371 now. A live person answers, and estimates are free.