Ghost Controls Gate Access Control Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Access Control in Highland Park: What to Know First

Ghost Controls gate access control repair in Highland Park typically runs $185 to $440 depending on whether we’re replacing a keypad, a receiver board, or rewiring the whole entry loop, and most callbacks are handled within one to two business days. We’re an independent Ghost Controls service provider, not a factory shop, which means we fix what’s actually wrong instead of selling you a whole new opener because the circuit board got wet. If your keypad stopped talking to the opener, your remotes lost their programming, or the gate now ignores the phone entry system, call (325) 936-1371 and we’ll walk you through what we’re seeing. This page is for Highland Park homeowners who own a Ghost Controls system and want straight answers about access control repair, parts, and honest pricing before anyone shows up with a multimeter.

Call (325) 936-1371

How Ghost Controls Products Fail - and How We Fix Them

We work on Ghost Controls openers more days than not, and the failure patterns are consistent. Here’s what we actually find on Highland Park service calls:

• AXDP and TSS1 keypads that go dead after a hard rain. The keypad housing on several Ghost Controls units has a gasket that shrinks in the Texas heat. Water gets behind the faceplate, shorts the ribbon cable, and the keypad still lights up but won’t send a signal. We replace the gasket, clean the contacts, and seal the housing with a bead of silicone rated for outdoor exposure here. If the board is already corroded, we swap in a new keypad and set the codes on site.
• Ghost Controls transmitter boards that drop every remote at once. This one is common on the AXDP receiver. The board’s memory chip loses its stored codes after a power flicker, which happens in Highland Park any time the storms roll through in spring. The fix is re-pairing every remote and adding a small inline surge protector on the low-voltage line so the next brownout doesn’t wipe it again. We’ve done this enough times that we keep the connectors in the truck.
• Gate opens but won’t close on auto-close. On Ghost Controls models with the auto-close feature, the culprit is usually a photo-eye that’s drifted slightly out of alignment, not a bad board. But on the AXDP line specifically, we sometimes find the auto-close timer chip has failed from heat. The giveaway is the gate closing once manually, then refusing to close again on its own. We test the photo-eye first, then verify the timer chip with a meter before we quote anything.
• Ghost Controls wireless intercom or phone entry that works only when you’re standing ten feet from the gate. The antenna wire on older units gets brittle and snaps inside the housing. Ghost Controls didn’t always strain-relief the antenna where it exits the control box, and years of opening and closing the lid flexes the wire until it breaks. We strip it back, resolder or replace the lead, and the range comes back. This is one of those repairs that takes twenty minutes once you know where to look.
• A gate that starts and stops in the same spot every single time. That’s the limit switch. On Ghost Controls openers the limit switch contacts arc and pit over time, usually on the close side. The gate reaches a certain point, the switch opens the circuit, and the gate stops dead. We replace the switch assembly with OEM whenever possible and adjust the travel so the gate seats cleanly without slamming. Aftermarket limit switches exist, but we’ve seen them wear out in half the time, which means you’re paying twice. For a part that lives outdoors in Texas, OEM is the better call here.

Our Ghost Controls Gate Access Control Process

Every Ghost Controls access control job follows the same path. We wrote it down so you know what to expect before we knock on the door:

1. 1
   You call (325) 936-1371. A live person answers. We ask what the gate is doing wrong, what model opener you have if you know it, and whether any remotes or keypads still work. That tells us which parts to load in the truck so we’re not making two trips.
2. 2
   We show up and test the system as a whole. We check the keypad, the remotes, the receiver board, the photo-eyes, and the limit switches. A Ghost Controls keypad that won’t work is often not the keypad at all, it’s a dead receiver or a bad ground. We trace it before we replace anything.
3. 3
   We quote the fix before we touch a screwdriver. The price includes parts, labor, and any welding or rewiring the job needs. You approve it first. Nothing gets added at the door.
4. 4
   We repair on site. If it’s a keypad, we replace and program it. If it’s a receiver issue, we repopulate the codes or swap the board. If the wiring leading to the keypad has been chewed by rats or baked by the sun, we pull new low-voltage line. The gate stays in your driveway the whole time.
5. 5
   We test every function. Keypad code, all remotes, auto-close, safety reversal, phone entry app if you have one. We don’t pack up until the gate opens and closes the way it should.
6. 6
   You get the 90-Day Done Right Promise in writing. If something related to our repair acts up within 90 days, call us and we’ll come back and make it right. No runaround and no new invoice unless you’ve asked for unrelated work. Hal Gatewood’s name is on that paper, and he means it.

What Ghost Controls Gate Access Control Costs in Highland Park

Here’s what Ghost Controls access control work actually costs in Highland Park. These are real ranges for common jobs, not phone-quote teasers:

• Keypad replacement (AXDP or TSS1): $185 to $265 installed and programmed
• Receiver board replacement: $220 to $340 depending on model and availability
• Remote reprogramming (full house of remotes): $85 to $140
• Photo-eye realignment or replacement: $95 to $175
• Phone entry or intercom integration: $300 to $440
• Full access control diagnostic visit (credited toward any repair): $75

What moves the price is parts availability and how much water or heat damage we find once the box is open. Ghost Controls still manufactures replacement parts for most current and recent-series openers, and we keep the common ones on the shelf. If a board is fried beyond repair and it’s a discontinued model, we’ll tell you honestly whether it’s time to move to a new opener and what that costs. The estimate is free, and the price we quote is the price you pay. Call (325) 936-1371 and we’ll give you a number before we set foot on the property.

Why Highland Park Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

We’ve been fixing gates in and around Highland Park since 2001, and Hal Gatewood has worked on the same driveway gate twice for the same family more than once. That’s the difference between a company that wants your money once and a shop that expects to see you at the hardware store. We answer the phone with a live person 24 hours a day, seven days a week. We don’t hide behind voicemail or route you to a call queue. The person who shows up is background-checked, uniformed, and has actually worked on Ghost Controls openers before, not reading a manual in your driveway. We also service LiftMaster, Mighty Mule, and DoorKing, so if your property has more than one brand on different gates, we handle all of it in the same visit. Every job carries the 90-Day Done Right Promise in writing. Not as a sticker on a truck, not as a phrase in a radio ad. Stamped on your invoice. And if the job is over $200, you get $40 off the repair without having to ask for it. Seniors and veterans get 10% off permanently. No trip charge inside the county. Tell me what it’s doing wrong and I’ll come take a look, here’s my cell.

FAQs

Get Your Ghost Controls Gate Access Control Working Again in Highland Park

If your Ghost Controls keypad is dead, your remotes won’t pair, or the gate’s ignoring your phone entry, call us at (325) 936-1371. We’ll answer with a live person, schedule a visit that fits your day, and give you a written price before we start. You don’t need a new opener because the board got wet or the limit switch wore out. You need someone who’s fixed enough Ghost Controls systems to know the difference in under an hour. That’s us.

Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Highland Park and nearby areas.