Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Gate Repair in Highland Park: What to Know First
Elite gate repair in Highland Park typically runs $285-$650 for operator and limit-switch work, and $180-$400 for hinge, weld, and realignment jobs. Most Elite repairs are done same-day because we carry the limit switches, control boards, and capacitors this brand eats through, plus we weld on-site so your gate never leaves the driveway. Call (325) 936-1371 and you’ll get a person, not a recording.
This page is for Highland Park homeowners who own an Elite slide or swing gate and want to know what’s actually wrong with it, what it costs to fix, and whether it’s worth repairing. We’re Gatewood Fence & Gate, and we’ve been fixing Elite gates in Highland Park since long before the neighborhood got trendy.
- Same-visit diagnosis: no charge to look at your Elite gate inside the county.
- 90-Day Done Right Promise: written on every invoice, not crammed into fine print.
- Independent Elite service: we are an independent Elite service provider, not an authorized dealer - that means we fix what’s broken instead of recommending what’s profitable to sell.
How Elite Products Fail - and How We Fix Them
Elite gates are honest workhorses, but after enough Highland Park heat cycles they fail in predictable ways. When we see a Elite sit dormant in a driveway, here’s what we usually find:
- SL-3000 slide operator limit switches scoring out. The nylon gears inside the limit assembly wear flat after 4-6 years of daily cycles, so the gate creeps past the close point or stops two feet short. We replace the switch assembly with the updated brass-gear unit and reset the run path. A homeowner could spend a month adjusting the remote and never fix it, because the problem isn’t the remote - it’s the switch telling the board it’s already closed.
- CSW-200 swing arm operator “dead at the keypad but the breaker’s fine.” This is the run capacitor, a forty-dollar part that Highland Park heat cooks slowly. The board stays lit, the motor just won’t start under load. We keep the right microfarad rating on the truck, because the wrong capacitor fries the motor in three months and that’s a $900 mistake dressed up as a cheap fix.
- Elite gate hinges seizing after a rain. Elite swing gates often run on pillow block bearings that look sealed but aren’t - not against a Highland Park downpour. Water gets in, rust starts on the inner race, and the gate sounds like a screen door dragging a cinder block. We pull the bearing, clean the shaft, and reset the gate on fresh bearings. Sometimes we can save the old ones with solvent; if not, we weld in new mounting plates right in the driveway.
- PR-1 keypad flaking and phantom triggering. The weather seal on the PR-1 face pad degrades in the Texas sun and lets moisture under the membrane. Once that happens the keypad sends signals it was never asked to send - the gate opens at 3 a.m. and the homeowner thinks the house is haunted. It’s the keypad. We swap in a sealed commercial keypad or a wireless retrofit, whichever the wiring supports.
- Elite swing arm mounting plate cracking at the weld. Highland Park soil shifts - everyone knows that - and when the post shifts even a quarter inch, the swing arm fights the gate instead of moving it. The stress concentrates where the arm bolts to the post plate, and the plate cracks at the weld. We cut the old plate off, set the post, and weld a thicker plate with better gussets. Fix the panel without the post and you’ll fix it twice.
Our Elite Gate Repair Process
Here’s what happens when you call us about a Elite gate:
- 1
You call (325) 936-1371. A live person answers - that’s Hal or his crew, not a call queue three states away. Tell me what it’s doing wrong and I’ll come take a look - here’s my cell.
- 2
We show up and listen. Before touching anything, we ask how long it’s been acting up, whether it got worse after a storm, and whether anyone’s worked on it recently. Half of what we know comes from what the homeowner tells us.
- 3
We diagnose Elite-specific issues. We start at the hinge post and follow the load path back to the operator. Elite failures are usually mechanical first and electrical second - we check the bearings, the chain or arm, then the limit switches and board.
- 4
You get the price before we turn a wrench. The number we quote is the number you pay. No “we found something else” money at the end. If you have a written estimate from someone else, bring it out - we’ll give you a free second opinion on it.
- 5
We fix it in place. Elite parts go in with basic hand tools and a welder, and we keep both on the truck. Unless your board needs bench programming, your gate stays in the driveway.
- 6
We run it through full cycles - open, close, obstruction, remote, keypad - then hand you the 90-Day Done Right Promise in writing. If anything fails inside 90 days, one call brings us back. No runaround.
What Elite Gate Repair Costs in Highland Park
| Repair | Typical range |
|---|---|
| Limit switch replacement (SL-3000, SL-1500) | $285-$420 |
| Hinge bearing replacement (swing gate) | $180-$350 |
| Weld repair on cracked post plate or arm | $240-$400 |
| Control board replacement (CSW-200, SL series) | $380-$650 |
| Gate realignment and full cycle test | $190-$330 |
What moves the price: how far gone the hinges are, whether the arm can be saved, and whether the board needs replacement programming or just a resistor swapped. We use OEM Elite parts when they’re still in stock and available, and quality aftermarket parts when OEM has been discontinued - and we tell you which one before we buy it. Every quote covers labor and parts. Estimates are free.
Why Highland Park Homeowners Call Gatewood Fence & Gate for Elite Work
We’ve been fixing gates in Highland Park since 2001 - before that, Hal Gatewood went to Eastfield College for welding and metal fabrication, then figured out he’d rather work outside than inside a shop. The name’s on the truck and the shop, and if you don’t like how a repair looks, you can drive over and say so in person. That’s the oldest accountability there is.
The 90-Day Done Right Promise isn’t just language - it’s stamped on every invoice. We don’t swap parts you don’t need, and we don’t push replacement on a gate that has another ten years in it. If your Elite opener is beyond saving but the gate itself is sound, we’ll tell you that too - and since we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, we know what’s compatible and what isn’t. One call, one honest answer.
FAQs
If your Elite product is still under manufacturer warranty, have that information ready when you call us - an independent repair may affect warranty coverage depending on the specific terms Elite sets, and we won’t guess about it. We’ll walk through the honest trade-off before any work begins. For most Elite openers in Highland Park, the warranty ran out years ago anyway - but if it’s still active, we’ll tell you straight.
Most Elite hinge, weld, and limit-switch repairs are completed the same visit. If we need a control board or a discontinued Elite arm, we’ll have it in hand before we schedule the return trip - usually one to three days in Highland Park. A live person answers our phone 24/7, so call (325) 936-1371 and we’ll give you a real window, not a six-hour “sometime.”
We keep the Elite parts that fail most often in Highland Park on the truck: limit switches for the SL-3000 and SL-1500, control boards for the CSW series, capacitors, remote receivers, and hinge bearings. If you need a part we don’t stock, we source OEM Elite when it’s available and quality aftermarket when OEM is discontinued - and we show you the difference before you pay for it.
A Elite gate is worth repairing if the post is sound and the gate panel hasn’t rusted through - that’s about 80% of what we see in Highland Park. A sagging gate in an otherwise good post is a hinge repair, not a replacement. Show me a gate that’s ten years old and never been serviced, and the opener might be done - but the gate probably has another decade in it if we catch the bearings before they seize.
Yes. We repair and replace the whole Elite setup - the operator, the chain or arm, the loop detectors, the photo eyes, safety edges, and the keypad wiring. On a Elite slide gate, a dead loop detector can make the gate ignore cars entirely, and that’s not an operator problem - it’s a wire in the ground. We find it and fix it.
Call Gatewood Fence & Gate for Elite Gate Repair in Highland Park
Tell me what it’s doing wrong and I’ll come take a look - here’s my cell. The phone number is (325) 936-1371, a live person answers, and the estimate is free. If you’ve already got a written quote from someone else, bring it out and we’ll give you a free second opinion on it. Highland Park is our backyard, and we’ve been keeping its Elite gates running for over two decades. We’ll be there.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Highland Park and nearby areas.