Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Motor & Opener in Highland Park: What to Know First
Ghost Controls gate motor and opener repair in Highland Park typically runs $180 to $540 depending on whether we’re replacing a control board, rewiring a limit switch, installing a new arm, or swapping the motor itself. Most jobs are done in one visit, same day when the parts are on the truck. We’re an independent Ghost Controls service provider, which means we work on your opener the way the factory manual suggests, without cutting corners. If your Ghost Controls opener is dead, beeping, or reversing for no good reason, the phone answer is (325) 936-1371 and a live person picks up. This page is for Highland Park homeowners who own a Ghost Controls opener and want straight answers on what’s wrong and what it’ll cost to set right.
How Ghost Controls Products Fail - and How We Fix Them
We work on Ghost Controls openers all over Highland Park. Most are the AXDP or TSS1 series on residential swing gates, with a few HYPRO units on heavier iron gates in the older sections of town. These systems are solid for the money, but they have patterns. Here’s what we see and what we do about it.
- Limit switches drifting on the TSS1: The magnetic limit assembly on the TSS1 sits inside the arm housing and picks up moisture from Highland Park humidity cycles. When the switch drifts, the gate stops short of the post or over-shoots and pops the breaker. Owners usually think the gate is “getting weak.” It’s not. We open the arm, replace the switch with an OEM unit or a sealed aftermarket equivalent, and set the limits the way the factory tells us to.
- AXDP control board losing its programming: A power flicker from a summer storm can scramble the travel settings on the AXDP board. The gate will then open about two feet and stop, or it’ll attempt to close and immediately reverse. We see this every June when the weather turns. We reflash the board, reprogram travel and force settings, and verify the battery backup is holding a charge. If the board is corrupted beyond repair, we quote an OEM replacement and tell you exactly why.
- Aluminum arm bracket stress cracks on AXDP swing openers: The bracket that mounts the arm to the gate post on the AXDP sees a lot of repeated torque where Highland Park picket gates catch the wind. We have found cracks in the bracket that never showed up on the homeowner’s radar because the crack sits behind the arm and only opens when the gate is at full extension. We weld the bracket in place, on the gate, in your driveway. Some companies will tell you to buy a new arm. We would rather fix the one that’s still straight.
- Worn spur gears inside the HYPRO drive: On heavier gates, the HYPRO’s gear stack takes a beating. When the grease dries out in the Texas heat, the gears whine and then start slipping. The gate will bind and the opener will fault out. We pull the drive, replace the gear set, pack it correctly, and send it back out. It saves the homeowner the cost of a whole new operator.
- Battery backup false-triggering the keypad alarm: Ghost Controls openers with the battery tray installed will sometimes false-alarm at the keypad when the battery terminals corrode in the summer humidity. The homeowner hears beeping and assumes the board is dying. We pull the battery tray, clean the terminals, test the battery, and the beeping stops without replacing a single part.
Our Ghost Controls Gate Motor & Opener Process
When you call us about a Ghost Controls opener in Highland Park, here is how the job goes.
- 1
Call and talk to a person: You call (325) 936-1371 and tell us what the opener is doing: won’t move, moves halfway, makes a noise, says something on the screen. We ask a couple of questions and set a time that works.
- 2
Show up and listen: We arrive, walk to the gate, and watch it run through its failure cycle. Most Ghost Controls problems reveal themselves in the first two minutes if you know what you are hearing.
- 3
Diagnose and show you what we found: We open the arm or the control box and point to the problem. We tell you the part cost, the labor cost, and the price before you approve anything. No surprises at the door.
- 4
Fix it right there: We carry Ghost Controls parts on the truck: limit switches, boards, remotes, keypads, battery trays, and arm hardware. If your job needs a part we don’t have, we order it and return, usually within a day or two.
- 5
Test the full cycle: We run the gate open and close ten times, check the safety reversal, confirm the keypad and remotes work, and verify the battery backup functions if installed.
- 6
Write you the promise: Every Ghost Controls repair leaves with the 90-Day Done Right Promise in writing. If the opener misbehaves again within 90 days, we come back and make it right.
What Ghost Controls Gate Motor & Opener Costs in Highland Park
Pricing for Ghost Controls work in Highland Park lands in a range that depends on what failed. A straight limit switch replacement on a TSS1 runs $180 to $240. Control board diagnostics and reprogramming on the AXDP is $140 to $260 if the board is good; a new board is $280 to $420 installed. A new arm assembly is $340 to $540, and a complete HYPRO repair with gear work runs $400 to $540. What moves the price is the age of the unit, the size of the gate, and whether we’re welding a bracket or replacing a drive component. Every job is quoted before we start. We also take $40 off any repair over $200, and seniors and veterans get a permanent 10% discount. Call (325) 936-1371 for a free estimate.
Why Highland Park Homeowners Call Gatewood Fence & Gate for Ghost Controls Work
We’ve been fixing gates in and around Highland Park since 2001, and Hal Gatewood’s name is on the shop and on every invoice. That means when something isn’t right, you know where to find us. We carry Ghost Controls parts on the truck, and since we also service LiftMaster, Mighty Mule, and DoorKing, we can tell you honestly whether your Ghost Controls opener is worth repairing or if you are better off replacing it. We never charge a trip fee inside the county, and we answer the phone with a live person 24 hours a day, seven days a week. When your gate won’t close and the opener is flashing an error, you don’t want to leave a message. You want a person. That’s us.
FAQs
No. As an independent Ghost Controls service provider, we use OEM parts and follow the factory installation and service procedures for your model, so the manufacturer’s warranty stays intact. We never cut corners or use a shortcut that would put your warranty at risk.
We’re in Highland Park most days and can usually be at your gate within 24 hours. Depending on the repair, we finish most Ghost Controls jobs in one trip. Call (325) 936-1371 to get on the schedule.
Most Ghost Controls openers we see in Highland Park are worth repairing. The AXDP and TSS1 are rebuildable systems, and a $200 limit switch or board repair is almost always a better call than a $1,200 new opener if the motor itself is still quiet. If the motor is burned or the arm is bent beyond straightening, we’ll tell you that too.
Yes. We install, test, and replace safety edges and battery backup trays on Ghost Controls gate openers. The battery tray is one of the most overlooked parts on these units, and a dead battery can make the opener throw false alarms at the keypad.
Many days, yes. Call (325) 936-1371 and tell us what the opener is doing. We’ll tell you honestly when we can be there, and we’ll quote you the repair before you commit.
If your Ghost Controls gate motor or opener is acting up in Highland Park, call (325) 936-1371. We’ll answer, we’ll show up, and we’ll stand behind the work. Tell me what it’s doing wrong and I’ll come take a look - here’s my cell.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Highland Park and nearby areas.