Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Parts & Welding in Highland Park: What to Know First
We provide independent Linear gate parts and welding in Highland Park, and most repair jobs are finished in a single visit, often the same day. Typical parts-and-welding work on a Linear gate runs $180 to $640 depending on whether it’s a hinge, a post, a rail, or custom fabrication, and you’ll get a written price before we strike the first arc. If you own a Linear gate in Highland Park and something’s sagging, grinding, or torn loose, call (325) 936-1371 and a live person picks up.
This page is for the homeowner who wants to know what’s actually wrong with their gate, what it’ll cost to fix right, and whether the part going on is worth the money. Hal Gatewood has been working on these systems since 2001, and we’ve seen every way a Linear gate can fail in this part of Texas.
How Linear Products Fail - and How We Fix Them
- Linear actuators (LRA and LS series) overheating in Texas summers. Highland Park gets stretches of 100-degree days, and Linear actuator motors run hot when the travel isn’t dialed in right. The gear oil thins, the motor labors, and the board eventually trips. We check the limit settings, gear backlash, and current draw before swapping any part. Sometimes it’s a $40 adjustment, not a $400 actuator.
- Hinge post sag on Linear swing gates. This is the one we see most. The hinge post loosens in the soil or the post-to-gate weld cracks, and the gate starts dragging the latch or the actuator. A gate sags in the hinge post, not in the middle, and that’s where we start. We re-set or replace the post, weld new hinge tabs, and the gate squares up again.
- Broken wheel trucks and rollers on Linear slide gates. Linear slide gate hardware uses a fairly soft nylon or steel roller, and on a heavy gate with a misadjusted track, the rollers chew themselves up fast. We’ve pulled flat-spotted rollers off of gates in University Park where the track had shifted a half inch. We replace the rollers, re-align the track, and the gate stops sounding like it’s dragging gravel.
- Gate rail welds cracking on fabricated steel frames. Highland Park gates built in the 1990s and early 2000s often have original Linear openers but steel frames that are now 20-plus years old. Weld joints at the rail corners fatigue, and you’ll see hairline cracking you can feel with a fingernail. We grind out the old weld, lay a fresh bead with proper penetration, and reinforce the gusset if the design needs it.
- Latch strike and lock mismatch after foundation movement. The clay soil under Highland Park moves. When it does, the gate post shifts, and a Linear gate that latched fine for years suddenly won’t catch. We re-align the strike, beef up the post if it’s moving, and sometimes we add a steel sleeve or a deeper post footing so it doesn’t shift again in the next wet-dry cycle.
Our Linear Gate Parts & Welding Process
- 1
Call and talk to a person. You reach us at (325) 936-1371, describe what the gate’s doing, and we schedule a time that works. No voicemail tree.
- 2
We show up and diagnose. Hal or one of his crew gets under the gate, checks the posts, hinges, rollers, rail, and opener. On Linear systems we specifically test actuator travel, gear wear, and board behavior before quoting anything.
- 3
Parts decision on the spot. For Linear openers, we put in OEM parts when they matter for function and warranty, and quality aftermarket parts where the OEM unit was the weak point anyway. We’ll tell you which is which and why.
- 4
On-site welding and repair. The gate stays in your driveway. We bring the welder, the steel, and the parts to you. No hauling the gate to a shop, no subcontractor, no “we’ll have to take it with us.”
- 5
Test everything, not just the fix. We run the gate through full cycles, check both travel limits, make sure the safety edges and obstruction reversal work, and verify the gate is balanced. If the opener is overworking, we fix that too.
- 6
You get the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. Plainly stated, on paper, on every job.
What Linear Gate Parts & Welding Costs in Highland Park
Here’s honest money for the common Linear jobs we do around Highland Park:
- Hinge replacement (welded steel hinges, both gates): $180-$340
- Post replacement with welding and concrete: $400-$850 depending on post size and gate weight
- Rail weld repair (hairline crack, grind and re-weld): $120-$280 per joint
- Custom welding or bracket fabrication: $90-$450 depending on the piece
- Gate roller and truck replacement on a slide gate: $160-$380
- Latch and lock repair or replacement: $110-$260
What moves the price is whether the post needs new concrete, whether the gate has to come off its hinges to get a good weld angle, and whether we’re patching a crack or rebuilding a failed joint. You’ll have the number before we start. No trip charge inside the county, and $40 off any repair over $200. Call (325) 936-1371 for a free estimate.
Why Highland Park Homeowners Call Gatewood Fence & Gate for Linear Work
Because when a Linear gate tears a hinge or the actuator pushes against a bent rail, the fix is welding and parts done in place, not a truck that hauls your gate away for two weeks. We’ve been at this in and around Highland Park since 2001. Hal Gatewood grew up about a mile from the Katy Trail corridor, and he’s worked on the same driveway gate twice for the same family. The name is on the shop, the shop is down the road, and the phone is answered by a person 24/7.
If your Linear opener is beyond saving, we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so you’re not starting from scratch with a new company. We also carry the 90-Day Done Right Promise on every job, and we offer a free second opinion on any written estimate. You can check our license, our address, and our work.
FAQs
Yes. We weld on site, in your driveway, in Highland Park or anywhere nearby. The gate stays where it is. We bring the welder, steel, and grinder to the job, and most hinge, post, and rail repairs are done in one visit. Call (325) 936-1371 and we’ll come look at it.
Common parts like rollers, hinges, latches, and photocells are on our truck or available within a day. Less common Linear board or actuator components are typically in hand within two to four business days. We’ll tell you at the quote stage if a part is special order, so you’re not wondering where your gate stands. Call (325) 936-1371 for an exact timeline.
Both, depending on the part. For circuit boards, safety edges, and limit switches, we use Linear OEM parts because those affect how the system behaves. For hinges, rollers, and weldable steel components, we often use heavy-duty aftermarket parts that outlast the factory originals. We’ll explain the choice for every part that goes on your gate. Call (325) 936-1371 to talk through your specific gate.
If the opener motor and gearbox are still sound, repair is almost always cheaper in the short run. We’ll tell you honestly when a Linear actuator has enough wear that a new openers makes more sense than feeding it parts. We service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, so if replacement is the right call, you have options. Call (325) 936-1371 and we’ll give you a straight answer.
Most hinge or rail welding jobs take two to four hours on site, including setup, welding, cleanup, and a full cycle test. Post replacement with new concrete adds time for the footing to set, usually a return trip the next day. Call (325) 936-1371 and we’ll give you a realistic window for your job.
Contact Hal Gatewood for Linear Gate Parts & Welding in Highland Park
If your Linear gate is sagging, grinding, or won’t latch, call (325) 936-1371. Tell us what it’s doing wrong and we’ll come take a look. Free estimates, a live person on the phone, and a written price before any work begins. Serving Highland Park and surrounding communities since 2001.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Highland Park and nearby areas.