Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Highland Park: What to Know First
Independent FAAC gate access control service in Highland Park usually costs between $195 and $650 depending on whether we’re replacing a keypad, rewiring a phone entry board, or troubleshooting a dead operator. Most FAAC access control jobs wrap up in one visit, and we quote the price before any work starts. If your FAAC keypad quit reading codes or the intercom rings but won’t release the gate, call (325) 936-1371 and we’ll figure it out.
This page is for Highland Park homeowners with a FAAC gate operator who need the access side working again - keypads, remotes, phone entry, card readers, video intercoms, or the smart access retrofit. We work on FAAC swing and slide gate operators as an independent FAAC service provider, which means we answer to you, not a manufacturer warranty schedule.
How FAAC Products Fail - and How We Fix Them
- FAAC 422 and 412 operator boards lose keypad programming after power flickers. Highland Park gets enough storm-driven brownouts that we see this monthly. The board’s EEPROM survives, but the relay outputs forget which accessory was on which channel. We reflash, re-map, and add a surge protector so it doesn’t happen again next storm.
- FAAC S418 and S450 slide gate units throw “obstacle” errors for no reason. Nine times out of ten it’s the encoder disc inside the gearmotor housing that’s cracked or slipping, not an actual obstruction. Dealers often quote a full operator. We replace the encoder, reset the limits, and the gate runs like new - usually under $300.
- FAAC E045 and E124 control boards show corrosion from gate-post moisture. The board sits in a polycarbonate box that breathes, and Highland Park humidity plus sprinkler overspray gets inside. Traces oxidize, the board gets flaky, and the gate starts opening on its own at 2 a.m. We clean, seal, and replace only if the board’s gone too far - and we’ll show you the corrosion before we quote a board.
- FAAC Photobeam and safety edge inputs stay armed, so the gate won’t close. FAAC uses normally-closed safety circuits. If a wire wiggles loose in the junction box under the gate post, the controller thinks a kid’s in the way. We trace the circuit, re-land the terminals, and the gate closes. Takes twenty minutes. Fix the wire, not the board.
- FAAC XK series keypads go dead from water getting behind the faceplate. The factory gasket dries out in Texas sun. Rain follows the weep groove, shorts the membrane, and the keypad either drops codes or lights up like a slot machine. We replace the membrane or the whole keypad with the proper IP-rated part and add dielectric grease to the connector so the replacement outlasts the original.
Our FAAC Gate Access Control Process
- 1
You call, a person answers. We ask what the gate’s doing wrong, what FAAC model you have if you know it, and when you’re home.
- 2
We show up in the window we promised. Hal or one of his crew rolls in with the diagnostic gear already in the truck. No “let me go back to the shop” on a first visit for access control.
- 3
We test everything that talks to the operator. Keypad, remote receiver, phone entry board, card reader, safety edges, photo eyes. We find the actual failure, not the first thing that looks loose.
- 4
We lay out the parts decision. OEM FAAC part if it’s warranty-sensitive or safety-critical. Quality aftermarket if it’s a relay or a transformer that doesn’t care who made it. We show you both prices before we order anything.
- 5
We fix it, test it, and hand you the remote count. Every access point gets cycled five times with a live test. Every code re-added. Every limit re-set.
- 6
We write the 90-Day Done Right Promise on the invoice. If anything we fixed acts up in 90 days, you call and we’re back. No charge, no debate.
What FAAC Gate Access Control Costs in Highland Park
Here’s what we’re seeing on real jobs around Highland Park right now. Every price is a range because the actual number depends on the model and what’s failed.
- Keypad replacement or membrane repair: $195-$395
- Phone entry board repair or replacement: $275-$550
- Card reader installation or retrofit: $340-$650
- Video intercom wiring and programming: $425-$780
- Board-level diagnostics and component repair: $180-$420
- Full access control retrofit on a FAAC gate with smart app: $850-$1,500
What moves the price: whether the operator brain is still good, how far the keypad is from the gate, and whether the original installer labeled the wiring. Most access control jobs land in the $195-$450 range. We quote it before we start, and the quote is the price. Call (325) 936-1371 for a free estimate - no trip charge inside the county.
Why Highland Park Homeowners Call Gatewood Fence & Gate for FAAC Work
We’ve been doing this since 2001. Hal Gatewood grew up about a mile from the Katy Trail corridor, and he’s worked on the same driveway gate twice for the same family more times than he can count. That’s not a talking point - it’s what happens when you stay in one place and your name’s on the shop.
Every FAAC job carries the 90-Day Done Right Promise, in writing, on the invoice. If it’s not done right, one call brings us back. We answer the phone around the clock - a live person, not a queue. And we don’t stop at FAAC. If the problem turns out to be a LiftMaster board or a Ghost Controls remote or an old DoorKing slide, we fix those too. Same truck, same visit.
Somebody in a call center three states away can’t weld a cracked FAAC gate bracket on your driveway. We can. That’s the difference.
FAQs
No. We’re an independent FAAC service provider, and U.S. law protects your right to have equipment serviced by whoever you choose. What voids a FAAC warranty is installing non-OEM boards or improper wiring. We use OEM FAAC parts anywhere a warranty claim could hinge on it, and we document every repair with photos and a written parts list so you have a paper trail if you ever need to file a claim with FAAC.
We stock the failure-prone items: E024/E124 relay boards, XK keypad membranes, photobeam ends, and encoder discs for the 412/422 operator series. Most FAAC access control repairs in Highland Park go same-visit with parts from the truck. If we need a specialized board, we have next-day availability from two independent FAAC parts distributors, not just the dealer channel. Call (325) 936-1371 and we’ll tell you the lead time before you commit to anything.
Same day for security-sensitive failures - a gate stuck open, an access point that won’t disarm, or an operator that keeps dropping codes. We keep emergency slots open every single day, and a person answers the phone when you call. If your gate is stuck closed and you don’t have an exit path, that’s also same-day. If it’s an intermittent annoyance, you’ll still get a scheduled window within a day or two, not a two-week wait.
Repair unless one of three things is true: the operator’s gearbox is grinding metal into the housing, the board is so corroded that three separate traces are gone, or the gate itself is sagging so hard the operator’s fighting the hinges every cycle. Two of those three are mechanical, not electronic - which means a new FAAC operator wouldn’t fix them either. We give you a straight answer before we quote a dime. Fix what’s failed, don’t swap what’s fine.
Both. We run the low-voltage wiring from the house to the gate, mount the entry station, program the directory, and tie it into the FAAC operator’s inputs - including dry contacts for gates with existing security or HOA systems. If your Highland Park home has phone entry wiring nobody labeled, we tone it out and map it rather than pulverizing your landscaping with a trencher to run new wire that was already there.
Tell me what the gate’s doing wrong and I’ll come take a look. Call (325) 936-1371 any time - you’ll get a real person, and we’ll get your FAAC gate access control working again.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Highland Park and nearby areas.