Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Farmers Branch
If you need Gate Installation - Farmers Branch or repair because a gate has stopped closing or a hinge has torn loose, the fix usually comes down to parts and welding done right the first time. We answer the phone around the clock at (325) 936-1371, and Hal Gatewood started this shop in 2001 so there’s a name and a face on every job. That matters around here because Farmers Branch gates run into a very specific set of problems: black clay soil, hundred-degree summers, and truck traffic that beats up commercial entrances along Valwood Parkway. We handle it all without hauling your gate away.
Most gate failures are not mysterious. A post heaves out of plumb, a hinge pin wallows out, a weld cracks at the rail. Our Gate Parts & Welding team fixes the gate in your driveway, on-site, and we stand behind it with the 90-Day Done Right Promise in writing.
Why Gatewood Fence & Gate Is Farmers Branch’s Preferred Gate Parts & Welding Company
We have been working in Farmers Branch long enough to know which gate problems repeat street by street. A residential gate off Valley View Lane tends to fail at the hinge post, where the black clay has swelled and shoved the post out of square. A commercial slide gate off I-635 tends to fail at the loop detector, where truck axles have cracked the wire and the gate no longer senses a car leaving. That kind of local knowledge only comes from doing the work here, not from a call script.
Every estimate we give is the price, agreed before we start. We do not change it at the door. Seniors and veterans get a permanent 10% discount, and any written estimate you got from another company we will look at for free as a second opinion. Hal’s name is on the shop and on every invoice. You can look us up.
Calls get answered by a live person, 24/7. Not a voicemail. Not a queue. You call (325) 936-1371 and somebody picks up.
Our Gate Parts & Welding Services in Farmers Branch
Hinge Replacement
A sagging gate is almost never the gate’s fault. It is the hinge, and the hinge is only as good as the post holding it. In Farmers Branch, we replace worn hinge assemblies on 1990s ornamental iron gates all the time. We match the original offset so the gate hangs true, drill and tap new threads rather than reusing stripped holes, and weld the hinge to fresh clean steel, not over rust.
Post Replacement
This is the big one for Farmers Branch. The black clay here heaves with every wet spring and dry summer, and an older gate post set in a shallow concrete pad will lean a little more each season. We cut the old footing out, dig deeper than the original, set the new post in a properly anchored base, and weld the hinge and latch plates back on. Fix the panel without the post and you will fix it twice.
Rail Repair
On long driveway gates, the top and bottom rails carry all the stress, especially if a windstorm or a delivery truck pushed the gate past its stop. We straighten bent rails in place where possible and weld in reinforcement where the rail has cracked at the stile. On commercial gates in the Valwood industrial corridor, we also re-weld rack teeth and re-shim gear track so the operator is not forcing a misaligned load.
Custom Welding
Not every repair is a one-for-one part swap. Somebody backed into the gate. A vandal cut through a rail. A hinge mount tore out and left an egg-shaped hole. We fabricate what is missing on-site: new latch brackets, gate ears, flat-bar bracing, anti-sag truss rods. The welding is done at your gate, in your driveway, while you watch. That is the way we like it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Farmers Branch
We are certified to service nine major gate brands, and the ones that show up most often in Farmers Branch are Elite, LiftMaster, and Mighty Mule. Whether you need a Farmers Branch Gate Motor & Opener for an older FAAC swing arm on a ranch-style driveway off Marsh Lane or a LiftMaster slide operator on a commercial lot near I-635, we stock the common consumables, can source the rest, and we do the mechanical welding and bracket work those operators need to mount correctly. Parts are ordered locally whenever possible so you are not waiting on a warehouse three time zones away.
Common Gate Parts & Welding Problems We See in Farmers Branch Homes
- Gate post heaving from black clay. This is the number one residential call. The post is not bent; the ground underneath it moved. We replace the post with a deeper, heavier base and re-hang the gate. This fix lasts because it addresses what actually happened.
- Rack and pinion binding on slide gates. When a post shifts even half an inch, the rack and the pinion start fighting each other. The operator pulls more amps, the thermal cutoff trips. We re-align the rack, weld the guide rollers to compensate, and quiet the whole system down.
- Loop detector failure in commercial aprons. Heavy truck traffic along Valwood Parkway cracks inductive loop wiring over time. A gate that does not sense exiting vehicles is not just annoying; it is a security and safety problem. We locate the break, saw-cut the apron, and splice in new loop wire so the gate detects vehicles reliably again.
- Heat-failed operator electronics. A first-generation swing operator mounted with no shade in a southwest-facing application will trip its thermal cutoff nearly every afternoon once Farmers Branch gets over 100°F. We relocate the unit where possible, replace degraded wiring, and upgrade the control board so the gate stops leaving the property open mid-cycle.
Pricing for Gate Parts & Welding in Farmers Branch, TX
Here are real numbers for the Farmers Branch market. Hinge replacement on a single ornamental iron driveway gate typically runs $180 to $340, including parts, welding, and labor. Post replacement is the bigger job: a single gate post set in new concrete and welded back to the gate frame runs $400 to $750 depending on depth and the size of the gate. Rail repair and straightening starts around $150 and goes up from there if we’re fabricating full replacement rails. Custom welding for brackets, ears, or a torn hinge mount usually lands between $120 and $400 depending on the extent of the fabrication.
Commercial slide gate work, especially loop detector re-wiring, is quoted per job because every apron is different. The estimate is free, the price is fixed before we start, and there is no trip charge inside the county. Call (325) 936-1371 and we will give you a number you can hold us to.
We Also Serve Cities Near Farmers Branch
Our Gate Parts & Welding in Farmers Branch crew picks up calls across the surrounding metro too. If you are in Highland Park, Dallas, Plano, or Irving and the gate is giving you trouble, call (325) 936-1371. Same shop, same promise, and we will show up when we say we will.
Serving Farmers Branch, TX - Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Farmers Branch
The gate is not what is moving. The post is. Farmers Branch sits on North Texas black clay that swells when it gets wet and shrinks when it dries. Each cycle works the post a little looser in the ground. You can keep adjusting the hinges, but until the post is pulled and reset in a deeper, wider footing, the gate will keep drifting. We do that work with the gate in place. Call (325) 936-1371 and we will come look at the post, not just the gate.
Almost always, you can keep the gate. We weld a heavy-duty mounting bracket to the gate frame, tie the operator into the post or a steel pad, and set the travel limits. The gate itself usually has years of life left, even if the hinge post is the part that needs work. We would rather repair what you have than sell you something new. A second opinion is free.
If the gate moves fine when you push the button but does not open automatically for an exiting car, the loop detector is usually the culprit. If the gate strains, grinds, or trips its breaker, the operator is suspect. Around Valwood Parkway, loop wire gets cracked by truck vibration far more often than operators die. We can put a loop tester on the apron and tell you which side of the control panel the problem lives on. Estimates are free.
The hinge post is leaning, or the hinges themselves are worn out of round. On a long gate, the moment arm compounds everything: an eighth-inch of hinge wear at the post translates to a two-inch drop at the latch. We replace the hinges with a heavier barrel and bush them properly, and we chase the real problem back to the post if it has moved. A diagonal anti-sag brace from top hinge to lower latch buys you decades on a wide gate. We weld that in place.
Yes. Gate Access Control in Farmers Branch like a keypad ties into the existing operator’s control board, usually at the open or wireless input terminals. We run the wiring, set the codes, and mount the keypad in a pedestal or on the post. No new gate, no new operator. This is common on commercial gates in Farmers Branch where delivery drivers and staff need entry after hours. Call (325) 936-1371 for an exact quote. Free estimates, always.
One More Thing About Farmers Branch Gates
Farmers Branch is not a typical residential suburb. The Valwood Parkway and I-635 corridors run commercial slide gates, barrier arms, and warehouse entrances all day, every day. When an eighteen-wheeler rolls over an inductive loop five hundred times a week, the loop wire fatigues, the controls lose their signal, and the gate either fails safe-open or stops sensing exit traffic entirely. Most residential gate companies never deal with that. We do, constantly. That is the difference between somebody who fixes gates and somebody who understands this specific city. The name is on the shop, and the shop is down the road, which is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Farmers Branch and the surrounding area since 2001.
If your gate is crooked, cracked, or not closing, call (325) 936-1371 today. A live person answers, every time, and the estimate is free. If it is not done right, we make it right. That is the whole promise.